Skip to content
Adtec Electrical Services

How much does downlight installation cost?

Downlight costs reflect the ceiling construction and lighting design as much as the number of fittings.

Short answer

Typical UK guide figures range from about £60–£120 per straightforward replacement fitting to around £90–£180 per point for new downlights with accessible wiring. Difficult ceilings, premium fittings and extensive making good can increase this considerably. These are not Adtec prices; Adtec gives a fixed written quote after seeing the job.

Typical UK guide figures for downlights

Typical UK guide figures for 2025–26, labour and materials, excluding VAT unless stated. Not Adtec prices; your job is priced after we see it.
Work or arrangementTypical UK guide figures
Replace a suitable existing fitting during a multi-light visit£60–£120 per point
New downlight point with accessible ceiling void£90–£180 per point
Six new standard points with straightforward access£550–£1,100
Compatible dimmer or control change alongside the work£50–£150+

These guide figures assume ordinary domestic access and suitable products, not major ceiling reconstruction. A single replacement can attract a minimum visit charge, so dividing a small bill by one fitting can be misleading. Premium architectural products, decorative repairs and additional circuits should be identified separately.

The lighting installation service covers the electrical side of a proposed scheme. Ask whether a quotation specifies the actual fittings or just a provisional allowance. Two prices for six downlights may describe very different light output, beam angles, drivers and installation methods.

Replacement fittings or a new lighting layout?

Existing holes may not suit a direct swap

A replacement may be relatively simple when the ceiling opening, cable condition and product requirements all match. However, old cut-outs can be too large or too small, and heat damage around earlier fittings can require attention. Some downlights use separate drivers, while others have integrated components. Matching appearance alone does not establish electrical compatibility or a suitable installation above the ceiling.

A new layout involves deciding where light is needed and then finding safe routes for the wiring. Joists, pipes and other services can rule out an apparently perfect grid. Review furniture and task locations before positions are marked. A smaller number of well-chosen fittings can give a more comfortable result than filling every available ceiling space with an identical bright beam.

Ceiling access, fire performance and insulation

Access from an empty loft may be easier than working below a finished bedroom floor. A flat roof, shallow void or tiled room above can require another approach. Ceiling construction also matters: recessed fittings must not undermine any required fire performance, and the selected product needs to suit the particular ceiling system rather than merely carry a general fire-rated label.

Insulation cannot simply be pushed over a fitting unless the manufacturer permits that arrangement. Required clearances, ventilation and any necessary accessories need to be established for the chosen product. Ask how airtightness, acoustic performance and moisture control will be maintained where relevant. Our loft conversion electrics guide explains why work around roof spaces needs coordination with the building design, rather than treating downlights as isolated holes in plasterboard.

Want a fixed written quote? Call 01235 430442 or send us the details.

Light quality, controls and room use

Choose the effect before the fitting

Warm or cool colour temperature changes how a room feels, while beam angle affects whether light spreads evenly or creates bright pools. Kitchens often need light directed onto worktops rather than behind the person cooking. Living spaces may benefit from separate groups or other lighting types so every activity does not require the whole ceiling to be switched on.

Dimming requires compatible lamps or drivers and a suitable dimmer; replacing the wall control alone may not prevent flicker or poor low-level performance. Explain whether you want simple switching, grouped zones or a more involved control system. For cooking spaces, coordinate with kitchen electrics. In bathrooms, product suitability and positioning depend on the zones and external influences, as discussed in bathroom electrical zones.

When to call an electrician

Ask for professional advice before cutting ceiling holes or buying a full set of fittings. This is particularly important where there is insulation immediately above the ceiling, a fire-separating floor, signs of overheating or uncertainty about the existing wiring. Stop using a fitting that smells burnt, crackles or shows heat damage, and arrange investigation rather than simply fitting a brighter replacement.

Older lighting circuits may need checks on earthing, protective devices and circuit condition before they are altered. Where additional work is necessary, it should be explained and priced as a defined part of the job. Domestic electrical services can cover the wider changes, while installation certificates explains the records associated with new electrical work. A lighting alteration and a full inspection of every circuit in the property are not the same service.

Comparing installation quotes without surprises

Provide room dimensions, ceiling height, the room above and any access restrictions. Share photographs of existing fittings and say whether the room will be decorated. Ask the quotation to identify fitting quantities, product specification, control arrangements, access openings and the standard of making good. Avoid comparing only a price per hole, which says little about the finished installation or the work necessary to achieve it.

Adtec provides a fixed written quote after seeing the job; the figures above are independent UK budgeting guidance rather than Adtec rates. Domestic work stays closer to Wantage, with wider coverage explained on areas we cover. Use contact to discuss your layout and timings. Agree who supplies fittings and who deals with plastering or decoration before ordering products, particularly if the finished ceiling must look consistent throughout an open-plan space.

Want a fixed written quote? Call 01235 430442 or send us the details.

Frequently asked questions

Only where the specific product and installation instructions permit it. Some require clearance or a particular arrangement, so a general claim about all LED fittings would be unsafe.

Replacing inefficient lamps with suitable LEDs can reduce lighting consumption. Savings depend on wattage, operating hours and how many lights are installed, so adding more fittings can offset part of the benefit.

The location must be assessed against bathroom requirements, including zones and product suitability. Ask the electrician to select the fitting for that position rather than choosing by appearance alone.

Not automatically, especially if the layout changes or cut-outs are oversized. Agree patching, plastering and decoration separately so the expected finish is clear before work starts.

Related pages

CallQuote