Skip to content
Adtec Electrical Services

Why have my outside lights stopped working?

Outdoor lighting failures can come from simple control settings or faults that need the supply left off.

Short answer

Check normal switches, timer settings and whether a daylight or motion sensor should be operating, without opening fittings or touching damaged equipment. If a protective device has tripped, or there is water ingress, damage, heat or a burning smell, leave the affected circuit off and arrange an electrician. Do not repeatedly reset a tripping circuit or bypass a sensor.

Start with the controls, not the wiring

Work out whether every outdoor light has stopped or only one fitting. A single failure can point towards that lamp, driver or local connection, while several lights failing together can involve their shared supply or controls. These are clues rather than a diagnosis. Make observations from a dry, safe position and avoid ladders, wet fittings and any damaged cables.

Check whether a normal wall switch has been turned off and whether a timer shows the correct time and programme. A power interruption may have changed stored settings. Some lights intentionally remain off in daylight, so a sensor-controlled fitting is not necessarily faulty because it will not operate at midday. Use only the manufacturer’s ordinary user controls and instructions; do not improvise wiring changes or conceal sensors to force operation.

If the fitting has a documented override mode, check how it is supposed to work rather than repeatedly flicking the supply. Different products respond differently, and random switching can make diagnosis harder. Outdoor lighting covers planned installations and replacements when the existing arrangement no longer suits the space.

When rain or damp is involved

Weatherproof does not mean maintenance-free

Water can enter through failed seals, cracked housings, loose cable entries or unsuitable joints. Condensation and corrosion can also affect outdoor equipment. A fitting may look intact from the ground while the electrical parts have become damp. If failures follow rain, tell the electrician about that pattern rather than assuming that waiting for dry weather has cured the issue.

Do not open a wet fitting, dry it with a hairdryer or add sealant around an unknown defect. Those actions can expose live parts or trap water inside. Where damage or water ingress is suspected, leave the affected supply off pending inspection. An appropriate repair may involve the cable entry, joint or routing as well as the lamp itself, so changing the bulb may have no effect on the real fault.

Tripped protection and shared supplies

An outdoor fault can operate an RCD or RCBO and affect other circuits or equipment, depending on how the installation is arranged. From a safe position, note which protective device has operated and what else lost power. Do not remove the consumer unit cover or keep resetting a device that trips. A repeat trip is information that an underlying problem still needs investigating.

Garden sockets, sheds, pumps and outside lights may share parts of a supply. Mention recent garden work, pressure washing, storms or newly connected equipment, but do not unplug or handle suspect outdoor equipment in wet conditions. Our RCD tripping guide explains protective-device behaviour, while fault finding addresses locating the cause rather than simply restoring power without knowing why it went off.

Want a fixed written quote? Call 01235 430442 or send us the details.

Lamps, drivers and sensors

The replaceable part depends on the product

Some fittings use a replaceable lamp; others have an integrated LED source or separate driver. A failed integrated unit may need a different repair or complete replacement. Check product information from a safe location before buying a lamp that may not fit. Never dismantle a sealed mains fitting or assume its internals are safe because the light is currently dark.

A motion sensor can be affected by its settings, obstructions, positioning or a fault. Plants growing across its detection area may change how reliably it notices movement. Only make adjustments intended for normal users, with safe access and in accordance with the instructions. If reaching the control requires work at height or exposure to electrical parts, leave it to a professional. Lighting installation can help when replacement controls or a new layout are appropriate.

When to call an electrician

Arrange investigation for repeated trips, unexplained intermittent failures, damaged cables, visible moisture, scorch marks or lights that flicker with crackling sounds. Switch off the affected circuit if safe and do not operate suspect equipment. For smoke, fire or immediate danger, leave the area and call 999. This is different from an ordinary appointment to diagnose lighting that has simply stopped working.

An electrician can check circuit condition, protective arrangements, insulation and the suitability of fittings for their environment. An outdoor product’s IP rating is only part of the assessment; installation position, cable entries and manufacturer instructions matter too. See domestic electrical services for related work, and garden room electrics where the fault involves a separate building or a wider garden supply rather than just one wall light.

What to send when arranging a visit

Provide the address, approximate number of lights, control type and a description of when the failure occurs. Photographs taken safely in daylight can show fitting types and likely access needs. Say whether anything has tripped, whether the fault follows rain and whether recent building or gardening work disturbed the area. Do not dig around cables or energise damaged equipment to gather more details.

Adtec works across Oxfordshire and surrounding counties, with domestic work staying closer to Wantage. Hours are Monday to Friday, 7:30am to 5:30pm; no emergency attendance is implied. See areas we cover and contact to discuss the work. If replacement is recommended, ask how the proposed fitting, controls and cable arrangements address the actual failure rather than choosing a similar-looking light and hoping the problem disappears.

Want a fixed written quote? Call 01235 430442 or send us the details.

Frequently asked questions

Intermittent operation may relate to a sensor threshold, timer programme, loose connection or moisture. Record when it happens without touching the fitting, because that pattern can help the investigation.

Do not alter mains wiring to bypass a sensor yourself. If you want ordinary switching instead, ask an electrician whether the fitting and existing wiring support a suitable control arrangement.

It needs the correct cap, size, electrical rating and compatibility with any controls or enclosure requirements. Follow the fitting instructions, and do not assume a lamp change resolves damaged wiring or water ingress.

Not necessarily; the defect could be in a fitting, joint, control or connected appliance. Testing is needed to establish the location and whether the cable is suitable to retain.

Related pages

CallQuote