Skip to content
Adtec Electrical Services

Is a commercial LED lighting upgrade worthwhile?

A successful commercial LED upgrade improves the working environment as well as reducing the electricity used by lighting.

Short answer

An LED upgrade is often worthwhile where existing fittings use more energy, give poor light or need frequent maintenance. The best solution comes from surveying the space, setting suitable lighting targets and comparing whole-life costs, not simply replacing lamps watt for watt. Emergency lighting, controls, access and verification should be included from the start.

Begin with the work, not the fitting catalogue

Write down what happens in each area and when. An office, dispatch bench, retail display and loading door need different treatment, even when they sit under the same roof. Ask staff where they struggle with shadows, glare or colour recognition. Those comments help identify problems that a simple count of existing lamps will miss.

A lighting survey should record dimensions, mounting heights, surface colours, daylight, obstructions and the positions of people and equipment. Note dirty lenses, failed lamps, flickering fittings and any improvised task lights. If the layout will change, design for the future arrangement rather than spending money reproducing a system that no longer suits the business.

Our commercial lighting service sits within wider commercial electrical work, so circuit condition and distribution can be considered alongside the light fittings. Establish who signs off the operational brief before product selection starts. A clear decision-maker avoids late changes when different departments have conflicting preferences.

Choose useful light rather than headline lumens

Illuminance, glare and colour

Illuminance is the light falling on a surface, measured in lux. A fitting’s lumen output describes emitted light, not how much reaches a desk or shelf. Optical distribution, mounting position, dirt and reflections all affect the result. Ask for a lighting calculation against the relevant tasks rather than assuming more lumens always mean a better workplace.

Glare can make a space uncomfortable even where average lux readings appear adequate. Bright exposed sources, reflections on monitors and fittings in drivers’ sightlines deserve attention. Colour rendering matters where staff inspect products or match finishes. Colour temperature affects appearance, but a higher kelvin value does not automatically improve accuracy or make a workplace safer.

For indoor workplaces, designers commonly use BS EN 12464-1 alongside task-specific guidance and the site risk assessment. Different activities require different maintained illuminance and quality criteria. Where high bays or racking are involved, our warehouse lighting levels guide explains why horizontal floor readings alone do not describe the full job.

Decide whether to relamp or replace

An LED replacement lamp can look economical, but compatibility must be checked. Existing ballasts, drivers, lampholders, wiring and enclosure condition may make conversion unsuitable. Some conversions alter the fitting’s original design and require a careful assessment of safety and responsibilities. A lamp advertised as a direct replacement still needs to match the exact application and manufacturer instructions.

Complete new luminaires often provide better optics, thermal management and control options. They may also reduce the maintenance burden associated with tired housings and brittle components. That does not mean every sound fitting must be discarded: the right decision depends on condition, available compatible components, intended service life and whether useful performance information is available.

Ask about driver replaceability, cleaning access, operating temperature and the availability of future replacement parts. An inaccessible fitting with an obscure sealed driver can be expensive to deal with later. Product life claims need context, including operating conditions and the performance measure used; they should not be read as a promise that every unit will run faultlessly for that period.

Use controls that match occupancy and daylight

Zones beat a single switch

Occupancy detection can reduce waste in intermittently used stores, meeting rooms and circulation areas. Presence and absence strategies work differently, so agree whether lights should start automatically or need manual switching. Sensor locations must account for partitions, racking and people sitting still. A nuisance system that repeatedly leaves staff in darkness will soon be overridden.

Daylight-linked dimming can be useful near windows and rooflights, but it needs commissioning against the actual working plane. Group fittings into sensible zones rather than letting one bright window dim a deep internal area. Set minimum levels and response times that suit the activity, and provide clear local controls where staff need an appropriate degree of adjustment.

Write a control schedule with operating hours, sensor coverage, time delays and any exceptions for security or cleaning. Identify who may change settings after handover. Controls reduce energy only when the installed configuration remains suitable, so include a short review once the business has experienced normal working patterns under the new lighting.

Want a fixed written quote? Call 01235 430442 or send us the details.

Calculate energy savings honestly

Compare measured or credible existing circuit power with the proposed system, including drivers and control gear. Multiply the difference in kilowatts by realistic annual operating hours and the business’s electricity unit rate. Keep standing charges out of a simple lighting savings calculation because changing fittings will not normally remove those charges.

For illustration, reducing connected lighting demand from 6 kW to 3 kW over 2,500 annual hours saves 7,500 kWh before any additional controls benefit. At an assumed 25p per kWh, that is £1,875 of electricity per year. These are worked assumptions (not typical UK guide figures for installation cost), not a forecast for your site or an Adtec installation price; substitute your own tariff and operating pattern.

Compare capital cost with electricity, cleaning, access equipment, replacement parts and likely maintenance visits over a sensible evaluation period. Avoid counting the same saving twice by applying occupancy reductions to hours that already exclude empty periods. Adtec gives a fixed written quote after seeing the job, so the installation scope and the business case can be reviewed separately.

Keep emergency lighting and electrical safety in scope

A normal lighting upgrade can change the appearance of escape routes and expose gaps in emergency coverage. Do not assume an emergency version of every new fitting is automatically the right design. The fire risk assessment, escape routes, open areas and points needing special attention should guide the emergency lighting review.

Existing emergency batteries, test facilities and records also need checking. A new normal lighting control arrangement must not inadvertently prevent emergency fittings charging or responding correctly. Read our emergency lighting testing guide and involve the person responsible for fire safety before changes are finalised, particularly where shared areas or landlord systems are affected.

The electrician should assess circuit condition, protective devices, switching and possible LED driver inrush current. A lower running load does not rule out starting-current or compatibility problems. Where the installation condition is uncertain, commercial EICR work can inform the wider plan, but an EICR is not a substitute for the design and certification of new work.

Programme installation around the business

Plan isolation, safe access and delivery routes before work begins. Work at height may need exclusion zones, clear floors and temporarily relocated stock or desks. Agree the operational impact with the business rather than assuming staff can continue underneath installation work. Adtec can discuss a phased programme, but access arrangements must be agreed for the actual site.

Check for asbestos information before disturbing older ceilings or associated building materials. Identify who removes redundant fittings and how lamps, batteries and other electrical waste will be handled through appropriate waste routes. Fluorescent lamps need care because they contain small quantities of mercury; they should not be broken into a general waste skip.

Include the ceiling finish, suspended grid condition and any fire compartment penetrations in the coordination discussion. Replacing a fitting may reveal damage that was previously hidden. Agree how unforeseen work is authorised, photographed and priced, and establish whether redecorating, ceiling repairs or IT moves are separate from the electrical quotation.

When to call a professional

Bring an electrician or lighting designer in when fittings repeatedly fail, staff report glare, layouts change or energy use no longer matches occupancy. Supply a floor plan, current lamp details, opening hours and any maintenance records. A short brief with clear priorities is more useful than a basket of products chosen before anyone has assessed the space.

At completion, request the appropriate electrical certification, product information, control settings and any agreed lighting verification results. Ask for a demonstration of manual overrides and emergency test arrangements. Record which circuits serve each zone so that future maintenance does not unnecessarily interrupt the whole business.

Finally, compare the finished installation with the agreed brief, not just a visual impression on a bright afternoon. Check representative working conditions and resolve sensor behaviour with the installer. Contact Adtec to discuss a surveyed upgrade, including access constraints and the documents you want included in the handover.

Want a fixed written quote? Call 01235 430442 or send us the details.

Frequently asked questions

They usually reduce lighting energy when they replace less efficient equipment, but the total bill also depends on operating hours and other business loads. Adding more fittings or leaving them on longer can offset part of the saving.

Sometimes, although existing dimmers and control equipment may not suit the proposed drivers. Agree compatibility and the control strategy before ordering fittings rather than assuming every LED behaves like the old lamp.

Not automatically: task, finishes and user comfort should guide the choice. A sample installation can help decision-makers compare appearance without committing the entire premises to one colour temperature.

No, normal lighting efficiency and emergency lighting reliability are separate issues. Any altered emergency system still needs the appropriate commissioning, records and ongoing testing.

Compare energy over representative operating periods and note changes in hours, occupancy and other equipment. Lighting submetering or circuit measurements can give clearer evidence than a whole-building bill alone.

Related pages

CallQuote